返回首頁 設為首頁 加入收藏
產品分類
脫硫脫硝環保裝備
浮法玻璃生產線
壓延玻璃生產線
玻璃深加工線
混凝土預制品生產線
電氣自動化
技術服務
公司主要業績
產品展示

   混凝土預制品生產線 >>  >> 預制混凝土模具
 
  
產品編號:
10005
產品名稱:
預制混凝土模具
規  格:
產品備注:
產品類別:
混凝土預制品生產線
 
   產 品 說 明
     隨著建筑市場的不斷發展,傳統的建筑現場澆砌模式資源利用率低、人力成本過高、安全系數較低和對環境的負面影響大等此類弊端與越來越嚴格的施工要求、能耗控制、安全保障、環境保護的矛盾日益凸顯。
預制是一種資源高效的建筑方式。與現場澆筑相比,工廠預制構件可提高施工速度,減少所需人員。施工中采用的預制構件可提供更加安全和健康的工作環境,物料搬運更加快捷,同時產生更少的廢料。此外,由于采用了高精度預制混凝土模具,降低了對水泥和鋼材的使用量,預制釋放的二氧化碳較現場澆筑施工相比大幅減少。
    我公司與Elematic合作開發出具有業內先進水平的預制混凝土模具。
主要技術指標Main performance
1)產品外形尺寸(長×寬):10600mm×3500mm  
2)模具表面平面度公差值≤4mm。
3)模具對角線尺寸誤差不超過±1mm。
4)模具邊緣直線度公差≤2mm。
    With the development of the construction market.The traditional ways of casting on site is low utilization rate of resources,high human cost,bad for the environment around and unsafe. All of these above formed a serious contradiction with the requirement of construction which is more and more strict,the environment protection,the safety factors,and the resource control.
    Precast concrete is a efficient construction method.Comparing with the old ways,it can improve the construction speed, reduces the need for Construction personnel, provide more safe and healthy working environment , make the material delivery more efficient and produce less waste. In addition, due to the high accuracy of precast concrete mold, it also reduces the use amount of cement and steel and carbon dioxide released by precast is much more less than casting on site.
    Our company and Elematic cooperation to develop a precast concrete mould is the advanced level in this area in China .
    The precast concrete mould developed by CTIEC and Elecmatic have reached to domestic advanced level.
The main technical parameters
1)Product size(Length x Width):10600mm×3500mm
2)The surface flatness tolerance of the mould≤4mm
3)The max diagonal difference of the mould±1mm
4)The straightness tolerances of the mould’s edge≤2mm
點擊數:3128  錄入時間:2015/3/16 【打印此頁】 【關閉

蚌埠凱盛工程技術有限公司系統版權所有 2015 版權所有
通訊地址:安徽省蚌埠市嘉和路481號 總機:0552-4126821 傳真:0552-4082809 郵箱:[email protected]
秒速时时彩平台